- 您现在的位置：买卖IC网 > Sheet目录368 > W25Q16DWSFIG (Winbond Electronics)IC FLASH SPI 16MBIT 16SOIC
W25Q16DW
7.2.25
Chip Erase (C7h / 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write
Enable instruction must be executed before the device will accept the Chip Erase Instruction (Status
Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “C7h” or “60h”. The Chip Erase instruction sequence is shown in Figure 24.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase
instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will
commence for a time duration of t CE (See AC Characteristics). While the Chip Erase cycle is in progress,
the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The BUSY
bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to accept
other instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit in the
Status Register is cleared to 0. The Chip Erase instruction will not be executed if any page is protected by
the Block Protect (CMP, SEC, TB, BP2, BP1, and BP0) bits (see Status Register Memory Protection
table).
/CS
/CS
CLK
Mode 3
Mode 0
0
1
Mode 3
Mode 0
Mode 3
0
1
2
3
4
5
6
7
Mode 3
In structio n
CLK
Mode 0
Instruction (C7h/60h)
Mode 0
IO 0
C7h/60h
DI
(IO 0 )
IO 1
DO
(IO 1 )
High Impedance
IO 2
IO 3
Figure 24. Chip Erase Instruction for SPI Mode (left) or QPI Mode (right)
Publication Release Date: September 06, 2012
- 49 -
Revision F
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
W25Q16VSFIG
IC FLASH 16MBIT 80MHZ 16SOIC
W25Q32BVZPIG
IC SPI FLASH 32MBIT 8WSON
W25Q32DWZEIG
IC FLASH SPI 32MBIT 8WSON
W25Q40BWSSIG
IC FLASH SPI 4MBIT 8SOIC
W25Q40BWZPIG
IC FLASH SPI 4MBIT 8WSON
W25Q64BVSFIG
IC SPI FLASH 64MBIT 16SOIC
W25Q64CVZEIG
IC SPI FLASH 64MBIT 8WSON
W25Q64DWZEIG
IC FLASH SPI 64MBIT 8WSON
相关代理商/技术参数
W25Q16DWSFIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIG
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSSIG
功能描述:IC FLASH SPI 16MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q16DWSSIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWZPIG
制造商:Winbond Electronics Corp 功能描述:IC FLASH 16MBIT 104MHZ 8WSON
W25Q16DWZPIP
制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16V
制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI